Browse all practice questions for the Turbine Overhaul (OH) Test 1 Practice. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Turbine Overhaul (OH) Test 1 Practice course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Which maintenance level corresponds to 'Line' or 'On wing'?
  • For a rotor with an odd number of blades, how many blades are replaced and what is the spacing between them?
  • Can an engine exceed 100% RPM without requiring an inspection, provided maintenance and flight manual guidelines are followed?
  • What is the definition of On Condition maintenance?
  • Which of the following is an example of a Special Inspection?
  • Maintenance is broken down into two categories. Which two categories are they?
  • Which statement best describes the cause of corrosion in turbine systems?
  • Does the engine run during a fluid wash?
  • Which statement is true about cycle definitions?
  • What is the first step in completing turbine overhaul?
  • Which statement best describes the orange zone around running engines?
  • What are some types of parts that will have life limits?
  • Flight time is the
  • Stress rupture cracks are caused by overtemperature and usually appear on which part of the blade?
  • Which surfaces are specifically mentioned as being susceptible to fouling?
  • What does a Service Check include?
  • During disassembly, you should do what to engine parts?
  • Go/no-go gauges are used to verify whether a dimension is within tolerance.
  • Who actually establishes TBO?
  • What are the two methods of compressor field cleaning?
  • For a rotor with an even number of blades, how many blades are replaced and what is the spacing between them?
  • What three plans must be established for the integrity of each life-limited part?
  • Is it true that 70-80% of performance loss in an operating gas turbine can be attributed to compressor fouling?
  • Which of the following is a Cold Section Component for inspection?
  • What is the final step described in a fluid wash process?
  • What are 2 categories of inspections that can be used on turbine engine parts?
  • Which statement best describes flight time?
  • Why must operating limitations be established?
  • Blade Creep is best described as:
  • To determine the scope of an over-temperature inspection, which reference should be consulted?
  • What is the definition of erosion in a gas turbine context?
  • Which factors define the extent of an over-torque inspection?
  • Where is FOD most found?
  • Which action is explicitly listed as the final step in the blade blending process?
  • Why are life-limited parts required on a turbine engine?
  • Which statement about the relationship between temperature, time, and inspection scope for over-temp events is correct?
  • During a fluid wash, what type of water is used?
  • Ink Marking Note: The note states that you should NOT use ink marking in which scenario?
  • The service management plan defines what?
  • Which inspections include Borescope inspection and Life Limited Parts replacement?
  • Non Routine (Unscheduled) maintenance is defined as:
  • CAMP stands for what and CFR does it follow?
  • Which statement about Cold Section inspection is true?
  • When should FPI be performed?
  • What is the main reason for a blade tip clearance inspection?
  • What is the primary purpose of compressor field cleaning?
  • What determines the extent of an over-temperature inspection?
  • What is the taxiing time also called?
  • In the blade blending steps, what is performed immediately after blending and before FPI?
  • What triggers FPI according to the procedure?
  • Plain water rinse may be used to desalinate if operating in a salty environment. What is the intended result?
  • Temporary markings include chalk, soapstone, ink markers with TEC marking, approved marking pencil (silver pencil), and tags/tape. Which of the following is a legitimate temporary marking option?
  • Hot Section Inspections are governed by what constraint?
  • What does the engineering plan contain?
  • Which of the following is a blade damage form listed in the hot-section damage types?
  • Abrasive grit wash uses which materials?
  • TRUE OR FALSE. Can some static parts move after supporting parts are removed?
  • If all factors above are favorable then TBO may be extended or eventually eliminated, allowing overhauls to be performed on what basis?
  • Block to block time is best described as
  • Which of the following best describes line or on-wing maintenance?
  • What instrument is used to check blade stretch from centrifugal loading?
  • In a wet motor check, which statement is true?
  • DOD stands for Domestic Object Debris and refers to debris related to which systems?
  • During an abrasive grit wash, is the engine operated while the wash is performed?
  • Ink Marking: Which statement is true?
  • Blade replacement uses which principle: weight-moment equality?
  • The FAA definition of a flight cycle is
  • In a dry motor check, which system is primed and leak checked?
  • CAMP stands for which phrase?
  • Which step in the turbine overhaul sequence involves putting components back together?
  • Blade Twist/Warpage is caused by ___?
  • For carriers operating under 14 CFR Part 121, CAMP is ...
  • How should FOD be prevented?
  • Maintenance has two levels. What are they?
  • What is the primary purpose of cleaning?
  • Which statement is true regarding blade damage types?
  • Which option best describes the dry motor check?
  • What surface should you NOT use electrolytic etch marking on?
  • What does Foreign or Domestic Object Damage refer to in turbine operation?
  • Which class of fire involves solids?
  • Which of the following is an example of a Special Inspection?
  • What effect does Foreign Object Damage have on the airstream?
  • What does 'on condition basis' imply for inspections?
  • Which class of fire involves electrical equipment?
  • Ground running for engine testing without flight will accumulate time.
  • Which option is NOT listed as a repair process?
  • All maintenance and inspections are based on what criteria?
  • Electrolytic Etch: Which statement describes it?
  • Taxiing before takeoff and after landing is included in flight time?
  • In the blade blending process, the first step is to determine if damage is within limits and repairable.
  • Stress Rupture Cracks usually appear as:
  • What is the FAA definition of flight time?
  • Which option is explicitly listed as a factor under Types of Cleaning?
  • Where would you find the info for timed tracked parts?
  • Which step immediately follows Cleaning in the turbine overhaul steps?
  • Which of the following is a hot section component for inspection?
  • Stress rupture cracks on turbine blades are caused by overtemperature and usually appear on the leading edge. Which option best reflects this statement?
  • Which device is used to quickly determine if a feature is within tolerance without providing an exact measurement?
  • The approved marking pencil (silver pencil) is categorized under which?
  • What is the consequence of continued heat exposure on turbine blades?
  • Which statement describes Major (Heavy or Shop) maintenance for aircraft engines?
  • Among permanent marking methods, which is described as the newest type?
  • What statement best describes the outcome when a turbine blade experiences creep under sustained heat?
  • What does FPI detect?
  • Dimensional inspection uses which set of tools?
  • What is considered line or on-wing maintenance?
  • List the events of an engine cycle
  • Which of the following is NOT a non-dimensional inspection method?
  • A ______ is used to perform inspections to ____ areas of a turbine engine by inserting it through special ____ in the engine cases
  • In the turbine overhaul steps, which step is the final stage?
  • Where to work around running engines. What is the orange zone called?
  • Which statement is true about the acronym FPI?
  • During an over-speed inspection, which condition describes when the extent of inspection is determined?
  • Does an abrasive grit wash fully clean hot section parts?
  • X-ray inspection is recommended for which parts?
  • Which step in the blade blending sequence directly enables detection of surface cracks?
  • Foreign Object Debris (FOD) refers to:
  • If cracks are found on a hot-section blade, what action is taken?
  • During hot section disk inspection, what is the consequence of finding any cracks?
  • Temporary marking can use ____ ONLY what is allowed by the manufacturer.
  • Which of the following is a cold section component for inspection?
  • Which maintenance level corresponds to 'Heavy' or 'Shop'?
  • In re-assembly after overhaul, what is the correct order of steps?
  • TRUE OR FALSE: Some static parts may move after supporting parts are removed.
  • Types of temporary markings: Which is a type of temporary marking?
  • The Hot Section Inspection interval is determined by what?
  • Are nylon or fiber-locks allowed in the engine hot section compartment?
  • DOD pertains to turbine engines or turbine auxiliary power units and refers to objects identified on the manufacturer's parts list or diagram as being parts of the engine or accessories to the engine or APU. This definition describes DOD as objects that are parts of what?
  • Which of the following is NOT listed as a damage type for turbine blades in the hot section?
  • Special Inspection is best described as which of the following?
  • Which of the following represents a listed engine removal and replacement reason?
  • Which class of fire involves liquids?
  • What is one of the most widely found forms of damage in the hot section of a gas turbine engine?
  • How should static parts be marked during disassembly?
  • Which of the following is a type of permanent marking?
  • Is it accurate to say that carbon build-up or ice shards can contribute to erosion damage?
  • Which phenomenon is described by particles entering through the inlet or gas stream and striking surfaces?
  • Cracks in a turbine blade are cause for _____ of the blade.
  • Routine (Scheduled) maintenance is characterized by:
  • All turbine engine inspections and maintenance are approved by the manufacturer and fall under FAA guidelines IAW Title which?
  • Which of the following is listed as a reason for engine removal and replacement?
  • In the blade blending process, what determines whether a blade should be repaired or replaced?
  • One purpose of cleaning is to remove coatings in order to permit inspection of base material. Which option reflects this concept?
  • Which statement best describes turbine engine inspections approvals?
  • Blade Creep is caused by which loads?
  • What does compressor fouling occur from?
  • Is it true that 70-80% of performance loss is due to erosion?
  • Serviceable limits for damaged turbine blades are more strict than those for turbine nozzle vanes. True or False?
  • What is the simplest blade replacement method to maintain balance?
  • Torque specifications in the manual are determined by which factors?
  • Which temporary markings should you NEVER USE?
  • Three plans together govern the integrity of life-limited parts. Which set of plans is correct?
  • What happens if damage is determined to be non repairable?
  • Which items are considered corrosive elements?
  • Which plan provides manufacturing constraints to produce life-limited parts?
  • Fan blade shingling refers to which phenomenon?
  • How is a blade's moment-weight defined?
  • Which statement about Hot Section inspection is true?
  • After performing FPI, which action might be required if necessary?
  • Galling is described as which of the following?
  • What is the primary purpose of using a borescope?
  • Domestic Object Debris (DOD) means with respect to turbine engines or turbine auxiliary power units, if part of the aircraft, objects or substances identified on the manufacturer's parts list or diagram as being parts of the engine or accessories to the engine or auxiliary power unit.
  • Modular engines __ ___ have a set TBO for the complete engine.
  • Which item is explicitly included in documented records after blade blending?
  • Which plan describes steps to withdraw life-limited parts from service?
  • Scheduled inspections are based on what time or cycle?
  • An abbreviated cycle is defined as?
  • What does the manufacturing plan identify?
  • Which of the following is NOT a hot section component for inspection?
  • What is the MOST CRITICAL portion of overhaul process?
  • Nylon / fiber-locks are allowed in the engine hot section compartment.
  • Who recommends TBO?
  • Not performing compressor field cleaning can lead to which consequences?
  • What is the FAA definition of an engine cycle?
  • During hot-section blade inspection, which procedure may be required?
  • If over-speed, Sudden Stoppage, FOD, or over-torque occur, what might happen to cold section inspection?
  • Which statement describes the difference between a flight cycle and an engine cycle?
  • What does FPI stand for?
  • What term describes the time from gate departure to gate arrival?
  • Which action is not listed as part of the blade blending process?
  • Which statement about marking static parts during disassembly is accurate?
  • Can bits of carbon build-up break free from nozzles or ice shards break away from the inlet and cause gradual erosion damage?
  • Can a scheduled inspection become an unscheduled inspection?
  • What does FPI aim to find?
  • What is the final action in the blade blending process?
  • Before the first run-up, engine and aircraft log-books are checked for which item?
  • Which statement about laser etching is true?
  • Service Check includes Layover plus what?
  • Which term describes metal transfer between rubbing surfaces due to fretting?
  • FOD can be large or small and isn't always easily identified. Which statement describes this characteristic?
  • CAMP follows which CFR for Part 121 operations?
  • Which of the following is a factor in determining the type of cleaning?
  • What does the service management plan define?
  • Can an engine go over its set parameters?
  • During a wet motor check, the engine is spooled with fuel, w/o igniters. Primes and leak checks which system?
  • Which of the following is NOT a listed temporary marking method?
  • What is a risk of excessive heat in a gas turbine engine?
  • Stress rupture cracks usually appear on turbine blades at which location?
  • Which of the following lists the three types of borescopes?
  • Can a plastic bag be considered FOD?
  • Who is authorized to perform overhaul?
  • What is the difference between a flight cycle and an engine cycle?
  • Which of the following is commonly a life-limited part in a turbine engine?
  • Layover Check includes which components?
  • Which statement best describes FPI?
  • The Layover Check comprises which of the following?
  • What does a typical fluid wash involve?
  • What is human error?
  • How should the disk in the hot section be inspected?
  • What normally causes stress rupture cracks?
  • Letter Check includes which of the following components?
  • What is the TBO definition?
  • Can trichloroethylene be used on titanium?
  • Letter Checks are inspections that occur at specified intervals and are based on what?
  • Which statement best distinguishes the two compressor cleaning methods?
  • Which statement about Special Inspection is true?
  • Which of the following is NOT a type of borescope?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy